Sharp DP-750 Manual de Serviço Página 114
- Página / 240
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
114 • Programmable Field Bus Controller 750-833
LED Signaling
WAGO-I/O-SYSTEM 750
Bus System
3.11.5 Fault Message via Blink Code of the I/O LED
Fault
Argument
Fault Description Remedy
Fault Code 1: Hardware and Configuration Fault
- Check sum fault in
parameter area of the
flash memory.
Switch off the supply voltage of the node.
Replace the coupler and switch on the supply
voltage again.
1 Overflow of the internal
buffer memory for the
inline code.
Switch off the supply voltage of the node. Reduce
the number of modules and switch on the supply
voltage again. In case that the fault still exists,
replace the coupler.
2 Unknown data type Detect faulty I/O module as follows: turn off the
power supply. Place the end module in the middle
of the field bus node. Turn the power supply on
again.
- If the LED is still blinking, turn off the power
supply and place the end module in the middle of
the first half of the node (towards the coupler).
- If the LED doesn't blink, turn off the power
supply and place the end module in the middle of
the second half of the node (away from the
coupler). Turn the power supply on again. Repeat
this procedure until the faulty I/O module is
detected. Replace the faulty I/O module.
Ask about a firmware update for the field bus
coupler.
3 Module type of the flash
program memory could
not be determined / is
incorrect.
Switch off the supply voltage of the node.
Replace the coupler and switch on the supply
voltage again.
4 Fault during writing in
the flash memory.
Switch off the supply voltage of the node.
Replace the coupler and switch on the supply
voltage again.
5 Fault when deleting the
FLASH memory.
Switch off the supply voltage of the node.
Replace the coupler and switch on the supply
voltage again.
6 Changed I/O module
configuration found after
AUTORESET.
Restart the coupler by switching the supply
voltage off and on again.
7 Fault when writing in the
serial EEPROM.
Switch off the supply voltage of the node.
Replace the coupler and switch on the supply
voltage again.
- Technical description 1
- Version 1.0.1 1
- Table of Contents 3
- 1 Important Notes 9
- 10 • Important Notes 10
- Legal Principles 10
- WAGO-I/O-SYSTEM 750 10
- Bus System 10
- Important Notes • 11 11
- 1.3 Symbols 12
- 1.4 Safety Information 13
- 1.5 Font Conventions 14
- 1.6 Number Notation 14
- 1.7 Scope 15
- 1.8 Abbreviation 15
- 2 The WAGO-I/O-SYSTEM 750 16
- 2.2 Technical Data 17
- Side view 22
- Dimensions in mm 22
- 2.3 Manufacturing Number 23
- 2.4 Component Update 24
- 2.6 Mechanical Setup 25
- Mechanical Setup 26
- 2.6.4 Spacing 27
- 2.6.6 Assembly Sequence 29
- 2.6.8 Power Contacts 31
- 2.6.9 Wire Connection 32
- 2.7 Power Supply 33
- 2.7.2 System Supply 34
- 2.7.3 Field Supply 37
- 2.7.5 Supply Example 42
- 2.7.6 Power Supply Unit 43
- 2.8 Grounding 44
- 2.8.2 Grounding Function 45
- 2.8.3 Grounding Protection 46
- 2.9 Shielding (Screening) 47
- 3.1 Description 49
- Description 50
- 3.2 Hardware 51
- 3.2.2 Device Supply 52
- 3.2.3 Field Bus Connection 53
- 3.2.4 Display Elements 54
- Hardware 55
- Hardware 56
- 3.2.7 Operating Mode Switch 57
- 3.3 Operating System 58
- 3.3.2 PFC Cycle 59
- Operating System 60
- 3.4 Process Image 61
- Process Image 62
- Programmable 63
- Fieldbus 63
- 3.4.4 Data Exchange 64
- 3.4.5 Memory Areas 64
- I/O modules 65
- 3.4.6 Addressing 67
- 3.6 Configuration 76
- Configuration 77
- 3.6.3 GSD Files 78
- 3.6.4 Identification Bytes 79
- 3.6.5 Example 83
- 3.9 Diagnostics 90
- 3.9.5 Device Status 92
- WAGO-I/O-SYSTEM 750 101
- 3.10.1 Data Areas 103
- 3.11 LED Signaling 109
- 3.11.2 Field Bus Status 110
- 3.11.4 Node Status 112
- LED Signaling 113
- the related function 117
- 3.12 Fault Behavior 119
- 3.13 Technical Data 120
- 4 Field Bus Communication 122
- 4.1.2 Wiring 123
- PROFIBUS 124
- PROFIBUS 125
- 5 I/O Modules 126
- 5.1.3 Analog Input Modules 129
- 5.1.4 Analog Output Modules 131
- 5.1.5 Special Modules 132
- 5.1.6 System Modules 134
- 5.2.1 2 DI I/O Modules 135
- 5.2.3 4 DI I/O Modules 136
- 5.2.4 8 DI I/O Modules 136
- 5.2.5 16 DI I/O Modules 136
- 5.2.6 2 DO I/O Modules 136
- 5.2.8 4 DO I/O Modules 137
- 5.2.10 8 DO I/O Modules 138
- 5.2.12 16 DO I/O Modules 138
- 5.2.13 Power Supply Modules 138
- 5.2.14 2 AI I/O Modules 139
- 5.2.15 4 AI I/O Modules 140
- 5.2.16 2 AO I/O Modules 141
- 5.2.17 4 AO I/O Modules 142
- 5.2.18 Counter Modules 143
- 5.2.19 PWM Module 144
- 5.2.20 Stepper Controller 144
- 750-630 145
- 750-631, 750-634, 750-637 146
- 750-635 146
- 5.2.24 Serial Interface 147
- 5.2.25 Data Exchange Module 148
- 5.2.26 DALI/DSI Master 149
- 5.2.27 AS Interface Master 149
- 750-660, 750-665, 750-666 150
- 5.3.1 Binary Input Modules 151
- 5.3.2 Binary Output Modules 152
- 5.3.3 Supply Modules 152
- 5.3.4 Analog Input Modules 153
- 5.3.5 Analog Output Modules 153
- 5.3.6 Special Modules 154
- 5.3.7 Field Bus Variables 155
- 156 • I/O Modules 156
- I/O Modules • 157 157
- 158 • I/O Modules 158
- I/O Modules • 159 159
- 160 • I/O Modules 160
- 5.4.1 Digital I/O Modules 161
- 162 • I/O Modules 162
- I/O Modules • 163 163
- 164 • I/O Modules 164
- I/O Modules • 165 165
- 166 • I/O Modules 166
- I/O Modules • 167 167
- 168 • I/O Modules 168
- I/O Modules • 169 169
- 170 • I/O Modules 170
- I/O Modules • 171 171
- 172 • I/O Modules 172
- I/O Modules • 173 173
- 174 • I/O Modules 174
- I/O Modules • 175 175
- 176 • I/O Modules 176
- I/O Modules • 177 177
- 178 • I/O Modules 178
- I/O Modules • 179 179
- 180 • I/O Modules 180
- I/O Modules • 181 181
- 182 • I/O Modules 182
- I/O Modules • 183 183
- 184 • I/O Modules 184
- 5.4.2 Analog I/O Modules 185
- 186 • I/O Modules 186
- I/O Modules • 187 187
- Information 188
- I/O Modules • 189 189
- I/O Modules • 191 191
- 192 • I/O Modules 192
- 7 6 5 4 3 2 1 0 194
- 15 14 13 12 11 9 8 7 194
- 15 14 13 12 11 10 9 8 196
- 5.4.5 Serial Interfaces 198
- 5.4.6 Data Exchange Module 199
- 5.4.8 DALI/DSI Master 201
- 5.4.9 AS Interface Master 202
- I/O Modules • 203 203
- 5.4.10 PROFIsafe Modules 204
- I/O Modules • 205 205
- 5.5.1 2 DI I/O Modules 206
- 5.5.3 4 DI I/O Modules 206
- 5.5.4 8 DI I/O Modules 207
- 5.5.5 16 DI I/O Modules 207
- 5.5.6 2 DO I/O Modules 208
- 5.5.8 4 DO I/O Modules 208
- 5.5.10 8 DO I/O Modules 210
- 5.5.12 16 DO I/O Modules 212
- 5.5.15 2 AI I/O Modules 214
- 5.5.16 4 AI I/O Modules 215
- 5.5.17 2 AO I/O Modules 217
- 5.5.18 4 AO I/O Modules 218
- 5.5.21 SSI Interface 222
- 5.5.25 DALI/DSI Master 224
- 5.5.26 AS Interface Master 224
- 6.1 Foreword 226
- 6.2 Protective Measures 226
- 6.3.3 Unit Categories 229
- 6.3.4 Temperature Classes 230
- 6.4.1 Divisions 232
- 6.4.3 Temperature Classes 233
- 6.5 Identification 234
- Explosion protection group 235
- (condition of use category) 235
- 6.6 Installation Regulations 236
- Installation Regulations 237
- 7 List of Literature 238
- 8 Index 239
Manuais e produtos relacionados com Digitalizar e Imprimir Sharp DP-750
Digitalizar e Imprimir Sharp MX-2700G Especificações
(127 páginas)
(127 páginas)
Digitalizar e Imprimir Sharp CD-M4000 Guia do Utilizador
(217 páginas)
(217 páginas)
Digitalizar e Imprimir Sharp ER-A440 Manual de Serviço
(108 páginas)
(108 páginas)
Digitalizar e Imprimir Sharp MX-2310U Manual de Serviço
(191 páginas)
(191 páginas)
Digitalizar e Imprimir Sharp MZ-80P4 Especificações
(25 páginas)
(25 páginas)
(100 páginas)
Digitalizar e Imprimir Sharp AR-4551 Especificações
(280 páginas)
(280 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.034 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais