Sharp ER-01PU Especificações descarregar pdf (Página 52)

ER-OIPU

2-2. Connection test (procedures when the ROM to

check the ER-OIPU in is used in the ER-OIPU)

(1) Connect the ER-OIPU’S RS232 connector to the RS232 connec-

tor on the COM 1 side of the PC with the RS232 cable.

COM1

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(lo)

(11)

ER-01 PU

-u

UKOG-6723RCZZ

Fig. 2

Turn on the power switch of the PC.

While pressing and holding “JF” key and “RF” key together, turn

on the power switch. (Master reset)

To charge the double-layer electric capacitor, lead the machine

for about 30 sec. Then turn off the power switch.

With “JF” key of the ER-01PU pressed, turn on the power

switch. (The machine enters the test mode.)

Insert the FD which includes the PC diagnostics test program

into drive A.

On the prompt of “C>” of the PC, enter “A:\Ol PUDIAG” and

press the enter key, and the diagnostics setting menu is dis-

played.

On the setting menu of the PC, select the item with the + key

and press the ENTER key. (Selection of set item)

Parity select:

Even/Odd/El

Data rate (bps): 2400/4800/9600/1 9200/-1

After completion of the PC setting, press the ESC key and the

ENTER key in this sequence. (The menu is displayed.)

On the menu screen of the PC, select a menu with the + key

and press the ENTER key. (Each test is performed.)

To cancel the test item, press the ENTER key of the PC.

To cancel the test mode perform the master reset.

Note:

@ The following set items must be common to the ER-OIPU

DIP switch setting and the PC setting. If not, the operation is

not performed properly.

Bit format/Parity select/Data rate

For details, refer to the “DIP switch table.”

@ The ER-01PU/PC RS232C cables must be as shown below:

ER-01PU Pc

SIGNAL PIN

PIN SIGNAL

RD : 2

SD : 3

x : : :;

ER :

DR : 6

x : : :;

SG : 5 —

5 : SG

*CABLE : SHIELD TYPE

3. Program code list

(1)

ER-OIPU stand-alone test

X After turning on the DIP switch, press the “ON-LINE” key to

start the test.

(2) Connection test with the host

X Select the test item on the menu screen of the host with the

+ key, and press the ENTER key to start the test.

Test NO.

Test item Stand-alone Connection

(Menu screen) test test with host

KEYILAMPIBUZZER

Included in

Diagnostics

AUTO.

001

MENU 01

(DIP SW ON/OFF

Swl-1 None

Diagnostics)

002

FUJPRINTER

Diagnostics

Swl -2 MENU 02

003

PRINTER CG

Diagnostics

SW1-3 MENU 03

004

DRAWER1 OPEN &

SENSE Diagnostics

Swl -4

MENU 04

005

DRAWER2 OPEN&

SENSE Diagnostics

SW1-5 MENU 05

006

(RS232 LOOP

Diagnostics)

SW1-6 None

FLASH ROM & CG

007

ROM SUM

SW1-7

MENU 06

Diagnostics

008

RAM Diagnostics SW1-8

MENU 07

009

AUTO Diagnostics Swl &sw2

ALL ON

MENU 08

010

AGING Diagnostics SW1 ALL ON

SW2 ALL OFF

MENU 09

PAPER END/NEAR

011 END/HEAD UP None

MENU 10

Diagnostics

012

A/D CONVERSION

Diagnostics

None

MENU 11

013

DIP SW& J1/J2

Included in

Diagnostics AUTO.

MENU 12

Test item

Diagnostics END

cancel

Auto end

MENU 17

Note: ( ) in the connection testis not displayed on the menu screen.

Only the aging test is terminated when the power is turned off.

(Either in the stand-alone test or in the connection test.)

●CONNECTOR: D-SUB 9PIN(MEAL) X 2pcs

150cm

●

Fig. 4

10-2

1 2 ... 47 48 49 50 51 52 53 54 55 56 57 ... 85 86

Comentários a estes Manuais

Sem comentários

Sharp ER-01PU Especificações Página 52

Comentários a estes Manuais

Manuais e produtos relacionados com Digitalizar e Imprimir Sharp ER-01PU