Sharp ER-01PU Especificações Página 23
- Página / 86
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
ER-OIPU
[Default]
DATA : “=”
(3Dh)
No. COMMAND
FUNCTION
CODE
44
ESC t n Select character code table
<1Bh><74h> n
[Function]
Selects the character listed on page “n” of the character code table.
Page Character type
o
USA:EUROPE
1
Japanese (Katakana)
2
Multilingual
3 Portuguese
I 4 I’Canadian-French I
[Notes]
If nothing is connected to the connector, bit Ois always equal to O.
When DTWDSR control is selected, the status is transmitted after the
printer confirms that the host computer is ready to receive data (DSR
signal is ON). If the host computer is not ready to receive data (DSR
signal is OFF), the printer waits until the computer is ready.
When XON/XOFF control is selected, one byte is transmitted without
checking if is ready to receive data.
This command is executed during receive buffer expansion. There-
fore, if there is other data in the receive buffer, some delay may be
caused between command receiving and status transmitting.
[Reference]
DLE EOT:
Transmit status in real time
GS a:
Transmit automatic status
GS r:
Transmit status
No. COMMAND
FUNCTION CODE
46
ESC
V Transmit paper detector status
cl Bh><76h>
5 Nordic
6 Greece
[Function]
Transmits the status of the paper detector when the command is
executed.
The status to be transmitted is as shown below.
[Default]
n=O
No. COMMAND FUNCTION
CODE
45
ESC u n
Transmit drawer
connector status
<1Bh><75h> n
[Range]
0 = 0,48
[Function]
Transmits the status of the drawer connector pin.
The status is as shown below.
I bit I Status 1/0
I
o Drawer Open/Close
1 Not defined
2 Not defined
3 Not defined
4 Fixed to O
5 Not defined
6 Not defined
7 Fixed to O
I bit I Function Value 0/1
I
I O I Near-end detector
I Paper is present/Paper is out I
1 Not defined
2 Journal-end detector
Paper is present/Paper is out
3 Receiot-end detector
Paper is present/Paper is out
4 Not used
Fixed to O
5 Not defined
6 Not defined
I
7 Not used Fixed to O
I
[Notes]
When DTWDSR control is selected, the status is transmitted after the
printer confirms that the host computer is ready to receive data (DSR
signal is ON). If the host computer is not ready to receive data (DSR
signal is OFF), the printer waits until the computer is ready.
When XONMOFF control is selected, one byte is transmitted without
checking if is ready to receive data.
This command is executed during receive buffer expansion. There-
fore, if there is other data in the receive buffer, some delay may be
caused between command receiving and status transmitting.
[Reference]
DLE EOT: Transmit status in real time
GS a: Transmit automatic status
GS r:
Transmit status
4-14
- SERVICEMANUAL 1
- CHAPTER 1. SPECIFICATIONS 2
- ❑ 0 ‘ ❑ on ❑ c 3
- I I I UNIT: mm 4
- Printer interface 5
- I Interface 5
- IPL interface 6
- 9. Dip switch 6
- 10. Drawer inteflace 7
- 11. Buzzer / Memory/ Backup 7
- CHAPTER 2. OPTIONS 8
- CHAPTER 3. INITIAL PROCESSING 9
- 4. COMMAND DESCRIPTION 10
- Command description 11
- I I I I I 15
- YOUR RECEIPT 18
- THANK YOU 18
- I No. I COMMAND/ 27
- ●2: Start code,Stop code 28
- Characters 31
- Fixed to o 33
- @ International character set 44
- CHAPTER 6. HEXADECIMAL DUMP 45
- CHAPTER. 7 :ERROR HANDRING 45
- CHAPTER 8. DISASSEMBLY& 46
- ASSEMBLY 46
- 3. REMOVE THE CONTROL PWB AND 47
- PANEL PWB 47
- REMOVE THE PRINTER UNIT 47
- REMOVE THE N/F PS PWB UNIT 48
- CHAPTER 9. INSTALLATION OF 49
- SERVICE OPTIONS 49
- [PARTS LIST’J 50
- [DISASSEMBLY METHOD] 50
- CHAPTER 10. DIAGNOSTICS 51
- FUNCTION 51
- 3. Program code list 52
- Test items 53
- 4-5. RS232 loop test 54
- 47. RAM test 54
- 4-8. Auto test 55
- 4-11. A/D conversion test 56
- 4-12. DIP SW & J1/J2 test 56
- Loading) MODE 57
- Description of main LSI’S 60
- 2) Blockdiagram 61
- Pin description 62
- 3. Memory map 63
- 4. Printer control 63
- Auto cutter control 64
- 3) Paper end sensor circuit 64
- ! Al— 1171-1255 65
- ISolder J2 alone 65
- 5) Head up sensor circuit 66
- IRPFA.Rece@t paper 67
- <>-m 68
- )))) .) I I I I I I 70
- 1. Control PWB 73
- L..------J 74
- Panel PWB 76
- N/F PS PWB 76
- SHARP PARTS GUIDE 77
- ❑ Exteriors 78
- ~] Exteriors 79
- ICore (OP12 X 15) 79
- ,VH i TA 80
- ❑ Control PWB unit 81
- ❑ Panel PWB unit 81
- , . . -,. m. . 82
- IlnclLldeNo 101-1171 I 82
- PARTS CODE 83
- ER-OIPUKA 84
- 1997 BY SHARP CORPORATION 86
- All rights reserved 86
- SHARP CORPORATION 86
Manuais e produtos relacionados com Digitalizar e Imprimir Sharp ER-01PU
(33 páginas)
(641 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.038 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais