Sharp ER-01PU Especificações Página 45
- Página / 86
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CHAPTER 6. HEXADECIMAL DUMP
This function is intended to print the data sent from the host com-
puter, using hexadecimal digits and characters corresponding to
them.
This function is started by turning ON the power while pressing the R
key and ended by turning OFF the power.
Example of hexadecimal print
123456789012345678901 234567890
Hexadec i maI Dump
1B 21 00 IB 26 02 40 . ! . .&. @
1B 21 04 IB 26 02 40 . ! . .&. Q
One line of data (7 units) is printed when received.
If the print data is less than one line, it is printed offline.
No functions other than
IDL~[EOTl / [DLE][ENQ] operate during the
hexadecimal dump.
After performing the hexadecimal dump, the processing before it is
not resumed and MASTER RESET
is made automatically.
CHAPTER. 7 :ERROR HANDRING
1. Error table
The following error states may be caused.
Error description Operating method in case of error detection
Auto cutter error Motor lock error described below is caused.
When status request is made, auto cutter
error is returned.
Head temperature Motor lock error described below is caused.
rise error When status request is made, head
temperature rise error is returned.
Thermal head
Motor lock error described below is caused.
thermistor’s
When status request is made,
breakdown
unrecoverable printer error is returned.
No thermal head
Motor lock error described below is caused.
connection When status request is made,
unrecoverable printer error is returned.
Head up error
Motor lock error described below is caused.
When status request is made, head up
lever open is returned.
Paper detector If paper-out error is detected by the
error
detector selected with ESC c 4, motor lock
error is caused.
When status request is made, paper-out
error of each detector is returned.
Data receive error
If the following errors occur while data is
being received through RS232, ? is printed
when bit 2 of dip switch 2 is so set as to
print ?.
● Parity error
● Framing error
● Overrun error
Buffer full error If print data is still received After completion
of data processing of one line, printing of
one line is performed automatically.
ER-OIPU
2. Motor Lock
If the motor lock is caused, the following operations are performed.
1)
2)
3)
4)
5)
6)
The error lamp goes on, the online lamp goes off and the buzzer
sounds intermittently.
In case of automatic status transmission, the status is transmitted
to the host computer via RS232.
The cause of error is removed.
By pressing the online key and receiving the [DLE][ENQ] com-
mand from the host computer, printing is resumed.
IDLE][ENQ][OO]: Restarts printing at the beginning of the line
where the error was caused.
IDLE][ENQ][O1]: Recovers from the error after clearing the
receive buffer and print buffer.
If the motor lock occurs during printing, a power failure mark is
printed and the interrupted printing is executed again.
After error recovery, the error lamp goes off, the online lamp goes
on and the buzzer stops sounding.
The following commands are processed even during motor lock.
IDLE][EO~[GS][ENQ]
3. Motor lock processing flow chart
Motor lock
ErrorlampON
Onlinelamp
OFF
Buzzersoundingintermittently
h
~ls datareceived?>
A
YES
<
[DEL][ENQ]
COMMAND?
T
YES
T
YES
Resumption;f printing/
LampOFFI BuzzerOFF
1
I
[
I
1
I
I
Clearingof receivebuffer
andprintbuffer
LampOFF/ BuzzerOFF
<
Is realstatus
transmitted?
YYES
I
Settingdatain
Transmissionofstatus
receivebuffer
I
1
v
6-1
- SERVICEMANUAL 1
- CHAPTER 1. SPECIFICATIONS 2
- ❑ 0 ‘ ❑ on ❑ c 3
- I I I UNIT: mm 4
- Printer interface 5
- I Interface 5
- IPL interface 6
- 9. Dip switch 6
- 10. Drawer inteflace 7
- 11. Buzzer / Memory/ Backup 7
- CHAPTER 2. OPTIONS 8
- CHAPTER 3. INITIAL PROCESSING 9
- 4. COMMAND DESCRIPTION 10
- Command description 11
- I I I I I 15
- YOUR RECEIPT 18
- THANK YOU 18
- I No. I COMMAND/ 27
- ●2: Start code,Stop code 28
- Characters 31
- Fixed to o 33
- @ International character set 44
- CHAPTER 6. HEXADECIMAL DUMP 45
- CHAPTER. 7 :ERROR HANDRING 45
- CHAPTER 8. DISASSEMBLY& 46
- ASSEMBLY 46
- 3. REMOVE THE CONTROL PWB AND 47
- PANEL PWB 47
- REMOVE THE PRINTER UNIT 47
- REMOVE THE N/F PS PWB UNIT 48
- CHAPTER 9. INSTALLATION OF 49
- SERVICE OPTIONS 49
- [PARTS LIST’J 50
- [DISASSEMBLY METHOD] 50
- CHAPTER 10. DIAGNOSTICS 51
- FUNCTION 51
- 3. Program code list 52
- Test items 53
- 4-5. RS232 loop test 54
- 47. RAM test 54
- 4-8. Auto test 55
- 4-11. A/D conversion test 56
- 4-12. DIP SW & J1/J2 test 56
- Loading) MODE 57
- Description of main LSI’S 60
- 2) Blockdiagram 61
- Pin description 62
- 3. Memory map 63
- 4. Printer control 63
- Auto cutter control 64
- 3) Paper end sensor circuit 64
- ! Al— 1171-1255 65
- ISolder J2 alone 65
- 5) Head up sensor circuit 66
- IRPFA.Rece@t paper 67
- <>-m 68
- )))) .) I I I I I I 70
- 1. Control PWB 73
- L..------J 74
- Panel PWB 76
- N/F PS PWB 76
- SHARP PARTS GUIDE 77
- ❑ Exteriors 78
- ~] Exteriors 79
- ICore (OP12 X 15) 79
- ,VH i TA 80
- ❑ Control PWB unit 81
- ❑ Panel PWB unit 81
- , . . -,. m. . 82
- IlnclLldeNo 101-1171 I 82
- PARTS CODE 83
- ER-OIPUKA 84
- 1997 BY SHARP CORPORATION 86
- All rights reserved 86
- SHARP CORPORATION 86
Manuais e produtos relacionados com Digitalizar e Imprimir Sharp ER-01PU
(33 páginas)
(641 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais