Sharp M450U Guia de Configuração Página 36
- Página / 93
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
SCANNING SETTINGS (ORIGINAL SIZE, EXPOSURE, RESOLUTION AND FILE FORMAT)
2-19
For resolution other than [200x200dpi], the [HALF
TONE] key can be selected.
INTERNET-FAX mode
Five selections are available for the resolution.
Touch the desired resolution key depending on the
original to be scanned.
For resolutions other than [STANDARD], the
[HALF TONE] key can be selected.
3
Touch the [OK] key.
You will return to the
initial screen.
SELECTING THE FILE FORMAT
When you send an image to one or more recipients, the [FILE FORMAT] key enables you to temporarily override the
individual file format settings (FILE TYPE / COMPRESSION MODE) stored for each recipient and send the image
to all of the recipients using a single file format setting.
"PDF MMR (G4)" is initially selected.
1
Touch the [FILE FORMAT] key.
"SELECT A FILE FORMAT
TO APPLY IT TO ALL
SCAN DESTINATIONS."
will appear in the message
screen. Touch the [OK]
key.
2
Select the file type and the compression mode.
(a) When the "SPECIFIED PAGES PER FILE"
checkbox is not selected, all scanned pages
are combined into a single file. When the
checkbox is selected, one file is created per
page from pages specified with.
(b) Touch the or key to set the number of
pages from which a file is created.
3
Touch the [OK] key.
You will return to the
initial screen.
AUTO
ORIGINAL
RESOLUTION
AUTO
EXPOSURE
STANDARD
FINE
SUPER FINE
ULTRA FINE
600
x
600dpi
READY TO SEND.
200
x
100
(
dpi
)
200
x
200
200
x
400
600
x
600
400
x
400
HALF TONE
OK
NOTE
The initial factory resolution setting is 300x300dpi
(SCAN mode) or Standard (INTERNET-FAX mode).
If desired, you can change the initial setting to a
different setting using the administrator setting,
"Initial resolution setting" (page 8-4
).
HALF TONE
OK
NOTE
This function cannot be used in Internet fax mode.
ORIGINAL
300
x
300dpi
RESOLUTION
PDF MMR(G4)
FILE FORMAT
EXPOSURE
AUTO A4
TIFFPDF
MH
(
G3
)
MMR
(
G4
)
NONE
FILE TYPE
PROGRAMMED
(
1-99
)
RESEND
OK
SPECIFIED PAGES PER FILE
COMPRESSION MODE
300
x
300dpi
ORIGINAL
RESOLUTION
AUTO
EXPOSURE
FILE FORMAT
(a) (b)
AUTO A4
READY TO SEND.
NOTES
● The initial file format setting can be changed with
the administrator setting "Initial file format setting"
(page 8-5
).
●
Even if you change the settings in the FILE
FORMAT setting screen, you can return to the
settings stored for each recipient by selecting
"PROGRAMMED" once again. The
[PROGRAMMED] key returns the file type to the
stored file format settings.
● When you perform a broadcast transmission, the
compression mode selected in the administrator
setting, "Compression mode at broadcasting
"
(page 8-5
)
, has precedence over the others.
MH
(
G3
)
MMR
(
G4
)
NONE
(
1-99
)
OK
PER FILE
COMPRESSION MODE
- OPERATION 1
- INTRODUCTION 2
- TABLE OF CONTENTS 3
- CHAPTER 1 5
- Scan modes 6
- Internet fax mode 7
- Data entry mode 7
- ACCESSING WEB PAGES 8
- Click here 11
- ■ Storing Groups 13
- SETTING UP SERVERS 14
- PAGE ("Passwords") 14
- BASE SCREEN 15
- ■ Address book screen 16
- FREQUENT USE ABCD 17
- CHAPTER 2 18
- SENDING AN IMAGE 19
- Touch the [SUBJECT] key 20
- READ-END 22
- Transmission 23
- Touch the [OK] key 24
- DESTINATION INPUT METHODS 28
- CANCEL SEARCH 29
- DETAIL OF 30
- BROADCAST XXXX 30
- NG000000 30
- START TIME STATUS 30
- BOOKLET TABLET 31
- (64 432) 32
- (64 297) 32
- SEND SIZE 33
- ENLARGEMENT TRANSMISSION 34
- SELECTING THE EXPOSURE 35
- SELECTING THE RESOLUTION 35
- SELECTING THE FILE FORMAT 36
- CHAPTER 3 37
- SPECIAL MODES 38
- (PROGRAM) 39
- ERASING EDGE SHADOWS (ERASE) 40
- DUAL PAGE 41
- TRANSMISSION) 42
- USING THE AUTOMATIC 43
- DOCUMENT FEEDER 43
- USING THE DOCUMENT GLASS 43
- CARD SHOT 44
- ■ USING CARD SHOT 45
- 50 pages 50 pages 46
- Original 46
- REPORT (TRANSACTION REPORT) 47
- JOB STATUS 48
- SETTINGS 48
- CHAPTER 4 50
- RECEIVING AN INTERNET FAX 51
- I-FAX MANUAL 52
- RECEPTION 52
- FORWARD] key 53
- Touch the [YES] key 53
- ■ Enabling inbound routing 54
- Click [Add] 55
- Enter a table 55
- ■ Activate the table 56
- CHAPTER 5 57
- PREPARATIONS FOR METADATA 59
- TRANSMISSION 59
- TRANSMITTING METADATA 60
- METADATA FIELDS 62
- CHAPTER 6 63
- STORING FROM THE OPERATION 64
- AMEND/DELETE 66
- PROGRAMMING A GROUP KEY 67
- STORING SENDER INFORMATION 69
- SENDER NAME 70
- STORING A GROUP INDEX 72
- STORING A PROGRAM 73
- EDITING AND DELETING PROGRAMS 74
- CHAPTER 7 75
- TROUBLESHOOTING 76
- IF YOUR E-MAIL IS RETURNED 77
- Touch the [LIST PRINT] key 78
- Original image samples 79
- CHAPTER 8 80
- ADMINISTRATOR SETTINGS 81
- SYSTEM SETTINGS 84
- I-Fax speaker volume settings 85
- Auto wake up print 85
- I-Fax send settings 86
- I-Fax receive settings 87
- PRINTING OUT SETTINGS 89
- CHAPTER 9 90
- NETWORK SCANNER / INTERNET 91
- FAX SPECIFICATIONS 91
- NUMBER OF ITEMS THAT CAN BE 92
- STORED WHEN A HARD DRIVE IS 92
- MXM450-EX1-IMAGE SEND 93
Manuais e produtos relacionados com Digitalizar e Imprimir Sharp M450U
(12 páginas)
Digitalizar e Imprimir Sharp X2 Manual do Utilizador
(137 páginas)
(137 páginas)
(108 páginas)
Digitalizar e Imprimir Sharp MX-M350 Especificações
(110 páginas)
(110 páginas)
Atec Narda-NBM-520 manuály
Uživatelské manuály a uživatelské příručky pro Zařízení Atec Narda-NBM-520.
Poskytujeme 1 manuály pdf Atec Narda-NBM-520 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Comentários a estes Manuais