Sharp AE-X9JJ Manual do Utilizador descarregar pdf (Página 8)

Type W-105-22FAB

1-1/4” O.D. x 5/16” I.D.

22 Teeth

MARTINDALE

• 1375 Hird Ave • Cleveland, OH 44107

Phone (216) 521-8567 • Fax Local 521-9476 / USA & Canada (800) 344-9191

E-Mail: [email protected]

Web Site: www.martindaleco.com

02/05

SOLID CARBIDE - TYPE SMF

COPPER SLITTING / RISER SLOTTING SAWS

NOTE:

For prices of thicknesses not

shown, use next higher price in

schedule. Other diameters, hole

sizes , thicknesses, number of

teeth, etc., also available on

application.

Thickness O.D. 2-1/2” 3” 4” 5” 6”

Hole 7/8” 1” 1” 1” 1”

No. of

Fraction Decimal Te eth 20 24 26 32 36

3/16” .1875” XSMFE1875 XSMFF1875 XSMFG1875

5/32” .1562” XSMFD1562 XSMFE1562 XSMFF1562 XSMFG1562

1/8” .1250” XSMFH1250 XSMFD1250 XSMFE1250 XSMFF1250 XSMFG1250

3/32” .0937” XSMFH0937 XSMFD0937 XSMFE0937 XSMFF0937 XSMFG0937

1/16” .0625” XSMFH0625 XSMFD0625 XSMFE0625 XSMFF0625 XSMFG0625

3/64” .0468” XSMFH0468 XSMFD0468 XSMFE0468 XSMFF0468 XSMFG0468

1/32” .0312” XSMFH0312 XSMFD0312 XSMFE0312

C-2 Carbide

Landed Teeth

Alternately Beveled Teeth

Hollow Ground For

Side Clearance

Used for cutting rolled Aluminum and Copper — materials that produce long, stringy chips.

Tolerances:

O.D. ±.005; Thickness ±.0005; I.D. +.001 -.000

Closer tolerances available at additional cost.

Alternately beveled teeth

(see sketch) produce

chips of less than the

width of the slot being

cut, eliminating the ten-

dency of chips to clog.

Keyways

are optional

at extra

cost.

Speed should be

approximately 50%

greater than HSS.

RESHARPENING

SERVICE

Complete resharpening

service is available.

Prices on application.

COATING

SERVICE

TiN, TiCN and other

surface coatings are

available.

Prices on application.

The two styles of saws shown are for Commutator Riser Slotting.

These saws are precision ground on all surfaces; dimensions are shown under the

actual size illustrations at right. Formed teeth are on center, with a 15° back-off and 45°

alternate bevel which is 1/3 the width of the tooth. Saws are hollow-ground to provide

clearance between the periphery and the hole.

Specify Thicknesses when ordering.

C-2 Solid Carbide.

Type W-75-18FAB

7/8” O.D. x 5/16” I.D.

18 Teeth

SOLID CARBIDE PRECISION

RISER SLOTTING / COPPER SLITTING SAWS / (JOYAL®)

Used for slotting copper commutator risers and other materials that produce long, stringy chips.

Catalog Number

W-75-20FAB, 7/8” x 5/16”, 18 Teeth . . . . . .TUNSW7518__ __ __ (*Specify Thickness)

W-105-30FAB, 1-1/4” x 5/16”, 22 Teeth . . . .TUNSW10522__ __ __

(*Specify Thickness)

*Saws are stocked in thicknesses from .010” through .069” in .001” increments.

Thickness tolerances are ± .0005”.

Rake Angle of

Teeth: 10° Positive

Metric Sizes

Available

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

Comentários a estes Manuais

Sem comentários

Sharp AE-X9JJ Manual do Utilizador Página 8

Comentários a estes Manuais

Manuais e produtos relacionados com Aparelhos de ar condicionado "split system" Sharp AE-X9JJ