Sharp e-Copy ShareScan Manual do Utilizador Página 1

Part Number: 73-00013 (5/2005)eCopy ShareScan® OPVersion 3.0Installation and Setup Guidefor Send to eCopy (for Sharp)

6 | Installation EnvironmentNovell supportWhen Novell client software is installed on the computer that is running the ShareScan OP Services Manager,

eCopy ShareScan OP Installation and Setup Guide | 7Installing the UPDD driverOverviewTo enable the touch screen on the ScanStation, you must install t

8 | Installing the UPDD driver6 Follow the instructions on subsequent screens until the Number of Devices window appears. Then enter the number of dev

eCopy ShareScan OP Installation and Setup Guide | 98 In the list of controller types, select Dynapro, SC3, Serial (the first item in the list) and the

10 | Installing the UPDD driverConfiguring the touch screenYou must configure and calibrate the touch screen only if you have a new ScanStation.To con

eCopy ShareScan OP Installation and Setup Guide | 113 On the Calibration tab, set the number of calibration points to 9. (The default is 2.)4 Click Ca

eCopy ShareScan OP Installation and Setup Guide | 13Installing eCopy ShareScan OPOverviewThe eCopy ShareScan OP Setup program installs the following c

14 | Installing eCopy ShareScan OP2 Click Next. If your computer does not meet the minimum requirements, Setup displays the following message:3 Click

eCopy ShareScan OP Installation and Setup Guide | 155 Click Next.6 Select the connectors you want to install and then click Next.If you selected a Lot

Licensing, Copyright, and Trademark InformationThe information in this document is subject to change and does not represent a commitment on the part o

16 | Installing eCopy ShareScan OPIf you do not plan to install the address book database on this computer, select No and then click Next. Then procee

eCopy ShareScan OP Installation and Setup Guide | 177 When the Ready to Install screen appears, click Install.8 When the installation is complete, cli

eCopy ShareScan OP Installation and Setup Guide | 19Licensing and configuring ScanStation OPOverviewYou license and configure the product from the Sha

20 | Licensing and configuring ScanStation OPLicensing the scanning deviceTo license the scanning device:1 Click Start Programs > eCopy Application

eCopy ShareScan OP Installation and Setup Guide | 213 Double-click System Information and then click Licensing.4 Enter the product key using either of

22 | Licensing and configuring ScanStation OP5 Click Activate Later. (You have 30 days to activate the license. See the Configuration Guide for more i

eCopy ShareScan OP Installation and Setup Guide | 23Configuring a connectorThis section describes the basic process of configuring a connector. To com

24 | Licensing and configuring ScanStation OPEnabling a connectorTo enable a connector:1In the console tree, click Devices > <ScanStation_name&g

eCopy ShareScan OP Installation and Setup Guide | 25Running the ScanStation clientTo run the ScanStation client:1In the console tree, click Devices &g

Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1About this guide . . . . . . .

26 | Licensing and configuring ScanStation OP3 On the Status tab, click Start. The client application opens.4 To quit the application, use one of the

eCopy ShareScan OP Installation and Setup Guide | 27Setting up Sharp MFP devices to use with Send to eCopyOvervieweCopy ScanStation OP enables users o

28 | Setting up Sharp MFP devices to use with Send to eCopyAfter creating the FTP site, perform the following steps:1 Open a Web browser and make sure

eCopy ShareScan OP Installation and Setup Guide | 29Creating a profile that uses a network folder (SMB)If you are using a shared network folder for st

30 | Setting up Sharp MFP devices to use with Send to eCopyCreating a profile that uses an FTP folderWhen you configure the MFP device, you specify in

eCopy ShareScan OP Installation and Setup Guide | 31Configuring Send to eCopyThe Send to eCopy tab is available on the eCopy ShareScan OP Administrati

32 | Setting up Sharp MFP devices to use with Send to eCopyUsing Send to eCopyWhen an MFP device is ready to use with Send to eCopy, the following pro

| 33IndexAactivating licenses 22administration console 3, 4installing 13opening 20Allow Anonymous Connections, importance of disabling 27Ccalibrating

34 | IndexServices Manager 3installing 13selecting 20shared foldercreating 27ShareScan OP 3installing 13ShareScan OP client 3ShareScan OP Services Man

iv | Table of ContentsSetting up Sharp MFP devices to use with Send to eCopy . . . . . 27Overview . . . . . . . . . . . . . . . . . . . . . . . . . .

eCopy ShareScan OP Installation and Setup Guide | 1IntroductionAbout this guideThis guide is intended for administrators responsible for installing eC

2 | IntroductionObtaining technical supportTechnical support is available to registered users from eCopy during the warranty period or for the duratio

eCopy ShareScan OP Installation and Setup Guide | 3ShareScan OP overvieweCopy ShareScan OP (Open Platform) extends the capabilities of digital copiers

4 | IntroductionThe ShareScan OP Services Manager and the connectors are installed on a network computer running Microsoft® Windows® 2000 or Windows X

eCopy ShareScan OP Installation and Setup Guide | 5Installation EnvironmentOvervieweCopy ShareScan OP is a client/server-based application. The ShareS