Sharp AR-F152 Especificações

MODELAR-F152• GETTING STARTED• MAKING COPIES• SPECIAL FUNCTIONS• SUPPLIES AND USER MAINTENANCE• COPIER TROUBLE? • APPENDIX 31220232736DIGITAL LASER CO

81Getting startedCOPIER INSTALLATIONImproper installation may damage the copier. Please note the following during initial installationand whenever the

91Getting startedCOPIER INSTALLATIONBe sure to allow the required space aroundthe machine for servicing and properventilation.A small amount of ozone

101Getting startedLOADING COPY PAPERThis copier is equipped with two paper trays. Load copy paper into the twopaper trays.Raise the handle of the pape

111Getting startedGently push the paper tray back into the copier.After loading copy paper, to cancel the blinking “P” without restarting copying,pres

122Making copiesMAKING COPIESThis chapter describes basic copying functions and some other copying functions using thebypass tray.NORMAL COPYINGThis c

132Making copiesNORMAL COPYINGPlace the original(s) face up in the document feeder tray or face down on the originaltable.A. When using the SPF:(1) Ma

142Making copiesNORMAL COPYINGTens digit Units digitWhen copying a book or an original which has been folded or a crumpled original,press down the ori

152Making copiesNORMAL COPYINGStream feeding modeThe stream feeding mode allows easy operation of continuous copying from the SPF.If the stream feedin

162Making copiesREDUCTION/ENLARGEMENT/ZOOMThree preset reduction ratios and two enlargement ratios can be selected. The zoom functionenables copy rati

172Making copiesBYPASS FEED (including special paper)The bypass tray automatically feeds up to 50 sheets of standard copy paper and also feedsspecial

FOR YOUR RECORDS ...To protect against loss or theft, record and retain for reference thecopier’s serial number located on the back of the unit.Model

182Making copiesBYPASS FEED Print facePress the tray select ( ) key to select the bypass tray. Set the number of copies ifusing standard

192Making copiesTWO-SIDED COPYINGFor tablet binding, turn the first copy over left to right as shown below. For bookletbinding, turn the first copy ov

203Special functionsSPECIAL FUNCTIONSThis chapter describes the special functions of this copier. Use these functions as needed.DESCRIPTION OF SPECIAL

213Special functionsTONER SAVE MODEPress and hold down the exposure mode selector key for approximately 5 seconds.The manual ( ) indicator will go out

223Special functionsUSER PROGRAMSPress the print ( ) key. The entered program number will be steadily lit and thecurrently selected parameter number f

234Supplies and user maintenanceSUPPLIES AND USER MAINTENANCEThis chapter describes how to replace the toner cartridge.Be sure to use only genuine SHA

244Supplies and user maintenanceTONER CARTRIDGE REPLACEMENTRemove the toner cartridge from the bag. Hold the cartridge on both sides and shakeit hori

254Supplies and user maintenanceTONER CARTRIDGE REPLACEMENTToner cartridge lifeTo find out the approximate quantity of toner remaining, follow the pro

264Supplies and user maintenanceUSER MAINTENANCETransfer chargerIf copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean

275Copier trouble?COPIER TROUBLE?This chapter describes misfeed removal and troubleshooting.MISFEED REMOVALWhen the misfeed ( ) indicator blinks or

1CONTENTS1 GETTING STARTEDINTRODUCTION 3CAUTIONS 4MAIN FEATURES 5PART NAMES 6OPERATION PANEL 7COPIER INSTALLATION 8CAUTIONS O

285Copier trouble?MISFEED REMOVALA Misfeed in the paper feed areaGently remove the misfed paper from the paper feed area as shown in the illustration

295Copier trouble?MISFEED REMOVAL●Do not touch the photoconductive drum (green portion) when removing themisfed paper. Doing so may damage the drum an

305Copier trouble?Rotate the feeding roller in the direction of the arrow and gently remove the misfedpaper from the exit area.Feeding rollerRaise the

315Copier trouble?MISFEED REMOVALE Misfeed in the SPFAn original misfeed may occur at one of three locations: if the misfed original is seen from the

325Copier trouble?DEVELOPER REQUIREDWhen the indicator lights up, the developer should be replaced.DEVELOPERREPLACEMENT SHOULD ONLY BE DONE BY AN AU

335Copier trouble?TROUBLESHOOTINGIf any problem occurs, check the list below before contacting your SHARP service center.See page:_12__13202035152515S

345Copier trouble?STATUS INDICATORSWhen the following indicators light up or blink on the operation panel or the following alphanumericcodes appear in

355Copier trouble?AUTOMATIC EXPOSURE ADJUSTMENTThe automatic exposure level can be adjusted to suit your copying needs. This level is set forcopying f

366AppendixAPPENDIXSPECIFICATIONSType Digital laser copier/facsimile, desk-top typeCopy system Dry, electrostatic transferOriginals Sheets, bound docu

376AppendixPower supply AC 120V (±10%), 60 Hz (±2%)Power consumption 1,000 WOverall dimensions 31.9" (W) x 19" (D) (809 mm (W) x 483 mm (D))

24SUPPLIES AND USER MAINTENANCE TONER CARTRIDGE REPLACEMENT 23– Toner cartridge life 25USER MAINTENANCE 25– Cabinet 25– Original tabl

386AppendixSUPPLIESTypes and sizes of copy paperFor best results, use only paper recommended by SHARP.Type of paperType of media Size WeightfeedingPap

396AppendixSUPPLIESProper storage1. Store the supplies in a location that is:●clean and dry,●at a stable temperature,●not exposed to direct sunlight.2

INDEXAAuto clear . . . . . . . . . . . . . . . . . . . . 20, 21Automatic exposure adjustment . . . . . . . 35Auto power shut-off mode . . . . . . .

Power on . . . . . . . . . . . . . . . . . . . . . . . . 12Power save modes . . . . . . . . . . . . . 20, 21Power switch . . . . . . . . . . . . . .

Date Issued:Nov. 1, 2000MATERIAL SAFETY DATA SHEETMSDS No. F-01001Section 1. Product IdentificationProduct:AR-152NT/T/FT/ST (Black Toner)Section 2. S

Section 6. Physical Chemical CharacteristicsBoiling / Melting Point: Not applicable Specific Gravity: 1.1Vapor Pressure: Not applicable Solubility in

Date Issued :Nov. 1, 2000MATERIAL SAFETY DATA SHEETMSDS No. F-31001Section 1. Product IdentificationProductAR-152ND/DV/SD (Black Developer)Section 2.

Section 6. Physical Chemical CharacteristicsBoiling / Melting Point: Not applicable Specific Gravity: about 7.3Vapor Pressure: Not applicable Solubili

MEMO

MEMO

31Getting startedGETTING STARTEDThis chapter provides basic information for using the copier.INTRODUCTIONThis copier has been designed to provide intu

MEMO

NOTICEBE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WARRANTY THATYOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user, of

PRINTED IN CHINA2000M KS TINSE0465QSZZAR-F152SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.www.sharp-usa.comSHARP CORPORA

41Getting startedCAUTIONSFollow the cautions below when using this copier.●The fusing area is hot. Exercise care in this area when removing misfed pap

51Getting startedMAIN FEATURESHigh-speed laser copying●Since warm-up time is zero, copying can be started immediately after the power switch isturned

61Getting startedToner cartridge lock release leverToner cartridgeSPF exit areaOriginal guidesFeeding roller coverDocumentfeeder trayTransfer chargerF

71Getting startedOPERATION PANELExposure mode selector key andindicatorsUse to sequentially select the exposuremodes: AUTO, MANUAL or PHOTO.Selected m