Sharp AR-C360P Guia de Instalação

1Table of ContentsNetwork Installation... 2Windows ...2Novell ...

10Windows® InstallationUSB Connection (cont’d)5 Install the User Documentation1. Insert the User Documentation CD (CD3) into your CD-ROM drive. The CD

11Windows® InstallationParallel Connection1 Connect the parallel Interface For direct connection to a PCThis port requires a bi-directional (I

12Windows® InstallationParallel Connection (cont’d)17.Click Properties → General Tab → Print Test Page. 18.Click the Print Test Page button.To Install

13Macintosh® InstallationNetwork Interface Connection •Requires Mac® OS 9.2 or 10.2.4, and above, running on a Macintosh comp

14Macintosh® InstallationOS 9.2 or above1 Install the Driver1. Turn the printer ON, then turn the computer ON.2. Place the driver CD (CD1), supplied w

15Macintosh® InstallationOS 9.2 or above (cont’d)3 User DocumentationFor additional information on using printer features as well as printer utilities

16Macintosh® InstallationOS 10.2.4 or above 1 Install the Driver1. Turn the printer ON, then turn the computer ON.2. Place CD 1, supplied with the pri

17Macintosh® InstallationOS 10.2.4 or above (cont’d)Install Printer Options1. Go to the Printer Setup Utility.2. Click Printer Info.3. Select Duplex U

18Service and Support• Consult the Sharp Authorized Dealer where you purchased your printer.• To find the authorized Sharp servicing dealer closest to

TrademarksAdobe and PostScript are trademarks of Adobe Systems, Inc. Which may be registered in certain jurisdictions.Microsoft, Internet Explorer and

2Network InstallationWindowsSelecting a printer driver in WindowsSelect a driver appropriate for your application. Fiery PostScript printer

Finisher Unit Installation GuideComponents1Finisher Unit7Inverter Stand2Finisher stand8Clear Band3Finisher Stacker9Band Stopper, Small4Finisher Cover1

23. Install the metal brackets where the breakout panels were.4. Open the face-up stacker (!), then open the flap and press it onto the stacker surfac

32. Remove the two bottom caps:a. Turn the inverter over. b. Remove the two screws securing the bottom caps on either side of the inverter.c. Remove t

45. Pull forward on the extension plate to disengage the pins from the top channel stops, then slide it down into the inverter and push back to engage

52. Attach the front of the inverter to the stand using two screws on either side.3. Attach the back of the inverter to the stand using one screw on e

63. Place the finisher cover near the back of the finisher. Locate the tab (!) on the right side of the cover.4. Hold the clear band perpendicular to

78. Pull the finisher platform about half way out, then loosen the screw on the locking piece (!: viewed from the opposite direction) so that it drops

12. Secure the stacker with four screws.13. Push the finisher against the printer until the prongs on the printer brackets fit into the holes in the f

9Application Notes & TipsUsing the Single Staple FeatureThere is a Staple dropdown selection within the Finishing Properties of the Fiery.There ar

10Saddle Stitching on Tabloid PaperThis section explains how to saddle stitch on Tabloid size paper, using the Postscript Driver (PS) and MS Word as a

3Network InstallationWindows (cont’d)2 Connect the Ethernet Interface 1. Switch off the printer and computer.2. Remove the protective cov

4Network InstallationWindows (cont’d)4 Install the Fiery PostScript® Printer Driver 1. Insert the drivers CD (CD1) into your CD-ROM drive. The CD will

5Network InstallationWindows (cont’d)6 Install EFI Fiery Utilities1. Insert EFI Utilities CD (CD2), into your CD-ROM drive. 2. Select your language.3

6Network InstallationWindows (cont’d)5. Select Two-Way Communications. 6. Type the Fiery IP address or DNS name. 7. To d

7Network InstallationNovell1 Install the UtilityThis utility installs, configures, and manages Sharp network print server devices.1. Insert the printe

8Windows® InstallationUSB Connection1 Connect the USB Cable For connection to a PC running Windows 98 or above Requires a USB cable vers

9Windows® InstallationUSB Connection (cont’d) 15.Click Finish to complete the Installation.16.If Connect cable screen is open, click Finish to