Sharp AL-1610 Manual do Utilizador

• GETTING STARTED• MAKING COPIES• STATUS INDICATORS• GENERAL INFORMATION2152432DIGITAL COPYING MACHINEOPERATION MANUALMODELAL-1600AL-1610Page

8GETTING STARTED4" (10 cm)Copier installationCOPIER INSTALLATIONImproper installation may damage the copier. Please note the followingduring init

9GETTING STARTEDCAUTIONS ON HANDLINGBe careful in handling the copier as follows to maintain the performance ofthis copier.Do not drop the copier, sub

10GETTING STARTEDCHECKING PACKED COMPONENTSAND ACCESSORIESOpen the carton and check to ensure that the following components andaccessories are include

11GETTING STARTEDSET-UP1Remove all pieces of tape. Then open the platencover and remove the protective material.2Use a coin (or suitable object) to re

12GETTING STARTEDSet-upSET-UPPressureplate lockScrew6Store the pressure plate lock which has beenremoved in step 5 and the screw which has beenremoved

13GETTING STARTED1Gently lift and pull out the paper tray until it stops.2Push the pressure plate down until it locks in place.3Fan the copy paper and

14GETTING STARTEDChanging the copy paper size in the tray1Gently lift and pull out the paper tray until it stops.2Push the pressure plate down until i

24STATUS INDICATORS1Open the bypass tray. Lift slightly on the side cover andslide the cover out until it stops.2Push gently the right side of the fro

25STATUS INDICATORS TD cartridge replacementTD CARTRIDGE REPLACEMENT5Remove the protective cover from the TD cartridge byunlatching three cover hooks

26STATUS INDICATORS1Open the bypass tray. Lift slightly on the side cover andslide the cover out until it stops.2Push gently the right side of the fro

FOR YOUR PROTECTION...To aid in reporting this compact copier in case of loss or theft, please record below themodel number and serial number located

27STATUS INDICATORSDRUM CARTRIDGE REPLACEMENT Drum cartridge replacement5Remove the new drum cartridge from the protective bagand gently insert the le

28STATUS INDICATORSMISFEED REMOVALThe copier will stop when a misfeed occurs. The misfeed ( ) indicator willblink.If paper is accidentally torn during

29STATUS INDICATORSMISFEED REMOVAL Misfeed removalRoller rotating knobA. Misfeed in the paper feed area1Push gently the right side of the front cover

30STATUS INDICATORSMISFEED REMOVAL Misfeed removalRoller rotating knobFusing unit release lever2Turn the roller rotating knob in the direction of thea

31STATUS INDICATORSMISFEED REMOVAL Misfeed removal3Close the side cover by pressing the handle on thecover.●The misfeed ( ) indicator will go out.Misf

32GENERAL INFORMATIONUser programsUSER PROGRAMSThe user programs allow the parameters of certain functions to be set,changed, or canceled as desired.L

33GENERAL INFORMATION4Select the desired parameter using the right copy quantity( ) key.●The entered parameter number will blink on the right side of

34GENERAL INFORMATIONPOWER SAVE MODESThe copier has two power save modes to reduce overall power consumptionthereby reduce the cost of operation. In a

35GENERAL INFORMATIONSetting the power save modesThe time that elapses before the copier enters a power save mode after anyoperation is made can be se

36GENERAL INFORMATIONUser maintenanceUSER MAINTENANCEProper care is essential for clean, sharp copies. Please take a few minutes toregularly clean you

1GETTING STARTEDSTATUS INDICATORSMAKING COPIESGENERAL INFORMATIONCONTENTS PageGETTING STARTED●CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . .

37GENERAL INFORMATIONCharger cleanerUSER MAINTENANCEUser maintenance1Turn the power switch off.2Open the bypass tray. Lift slightly on the side cover

38GENERAL INFORMATIONProblem Solution●Copier plugged in?●Power switch ON?●Copy density properly adjusted?●Is the original placed face down?●Paper to

39GENERAL INFORMATIONThe TD cartridge is not installed. Install theTD cartridge.Side cover is open.Close the front and side covers securely.The TD car

40GENERAL INFORMATIONSUPPLIESTypes and sizes of copy paperSize Weight Capacity Special paper(21 lb. bond paper)Paper tray 5-1/2" x 8-1/2" 15

41GENERAL INFORMATIONSUPPLIESGenuine supplies statementStandard supplies for this copier that are to be replaced by the user are copypaper, TD cartrid

42GENERAL INFORMATIONMOVING INSTRUCTIONSWhen moving this copier, follow the procedure below.When moving this copier, be sure to remove the TD cartridg

43GENERAL INFORMATIONType Digital copying machine, desktopCopy system Dry, electrostatic transferOriginals Sheets, bound documentsOriginal sizes Max.

44GENERAL INFORMATIONSPECIFICATIONSSpecificationsOverall dimensions 23-15/64" (W) x 20-23/32" (D)(with bypass tray folded) (590 mm (W) x 526

45GENERAL INFORMATIONAAuto clear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Automatic exposure adjustment . . . . . . .

46GENERAL INFORMATIONSScrew . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11, 42Special paper . . . . . . . . . . . . . . . .

2GETTING STARTEDCautionsCAUTIONSFollow the cautions below when using this copier.●The fusing area is hot. Exercise care in this area when removing mis

47SHARP Date Issued:Nov. 1, 1998MATERIAL SAFETY DATA SHEETMSDS No. F-00841Section 1. Product IdentificationProduct:AL-160TD (Black Toner)Section 2. Su

48Section 6. Physical Chemical CharacteristicsBoiling / Melting Point: Not applicable Specific Gravity: 1.1Vapor Pressure: Not applicable Solubility i

49SHARPDate Issued :Nov. 1, 1998MATERIAL SAFETY DATA SHEETMSDS No. F-30841Section 1. Product IdentificationProductAL-160TD(Black Developer)Section 2.

50Section 6. Physical Chemical CharacteristicsBoiling / Melting Point: Not applicable Specific Gravity: about 7.3Vapor Pressure: Not applicable Solubi

51MEMO

MEMO

WARNING:FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void t

PRINTED IN JAPAN99A KS➀TINSE0109QSZZAL-1600/AL-1610SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.SHARP ELECTRONICS OF CANAD

3GETTING STARTEDMain featuresMAIN FEATURESq High-speed laser copying●First-copy time is only 7.2 seconds (except in a power save mode or immediately a

4GETTING STARTEDPART NAMES AND FUNCTIONSOverall layoutPart names and functionsq Platen coverPlace the original on the original table and close theplat

5GETTING STARTEDPART NAMES AND FUNCTIONS!5 Drum cartridge handle Hold to pull out the drum cartridge.!6 Drum cartridgeCopy images are formed on

6GETTING STARTEDOperationpanelPART NAMES AND FUNCTIONSPart names and functionsq AUTO/MANUAL/PHOTO ( / / ) keyand indicators (p. 15)Use to sequentially

7GETTING STARTEDPART NAMES AND FUNCTIONS!2 Zoom keys (p. 17)Use to select any reduction or enlargement copy ratiofrom 50% to 200% in 1% increments.!3