Sharp R-210B Manual do Utilizador descarregar pdf

Receiving, Inspection & Unpacking

General Installation

When the equipment is received all items should be carefully checked against the bill of lading to be sure all crates

and cartons have been received. Before accepting delivery, carefully inspect each carton or crate for visible shipping

damage. If any damage is noticed, the carrier should make the proper notation on the delivery receipt acknowledging

the damage. Make notations of all damage on all copies of the bill of lading and have all copies countersigned by

the delivering carrier. The carrier should also fill out a Carrier Inspection Report. The factory Traffic Department should

then be contacted. File claim for damage with the carrier. Physical damage to the unit after acceptance is not the

responsibility of Twin City Fan Companies, Ltd.

Unpack each carton or crate and verify that all required parts and proper quantities of each item have been received.

Refer to drawings for part descriptions. Report shortages or missing items to your local representative to arrange for

replacement parts.

Due to availability of carriers and truck space, it is not possible to guarantee that all items will be shipped together.

Verification of shipments must be limited to only those items on the bill of lading.

The unit nameplate must be checked to make sure the voltage agrees with the power supply available.

CAUTION: Sheet metal parts, screws, clips and similar items inherently have sharp edges, and it is necessary that the

installer and service personnel exercise caution.

The installation of this equipment shall be in accordance with the regulations of authorities having jurisdiction and all

applicable codes.

This equipment is to be installed by an experienced installation company and fully trained personnel.

The mechanical installation of the exhaust ventilator consists of making final connections between the unit and build-

ing services, duct connections.

Nomenclature

B CR U R - 120

D = Direct Drive

B = Belt Driven

CR = Centrifugal Roof Exhauster

CL = Centrifugal Low Profile

D = Downblast

U = Upblast

W = Wall Exhauster

H = Hooded

P = Penthouse (Louvered)

Fan Size

R = Restaurant

SH = Smoke & Heat

Models

DCLH, DCLP, DCRD, DCRU, DCRUR, DCRW, DCRWR

BCLH, BCLP, BCRD, BCRD-E, BCRU, BCRUR, BCRW, BCRWR, BCRUSH

Twin City Fan & Blower Catalogs 4050, 4105 and 4135 provide additional information on this equipment. These cata-

logs can be found at www.tcf.com or by contacting your local Twin City Fan & Blower sales representative.

IM-4050

August 2014

Centrifugal Powered

Roof & Wall Exhausters

INSTALLATION, OPERATION & MAINTENANCE MANUAL

1 2 3 4 5 6 ... 15 16

Resumo do Conteúdo

Página 1 - Roof & Wall Exhausters

Página 2 - Shipment of Motors

10 Twin City IM-4050Dimensions and WeightsModels DCRU/DCRURMODELDAMPERSIZECANTEDCURB SIZESELF FLASHCURB SIZEBCRU BCRUR110B 110B18 x 18 221⁄2 x 221⁄2

Página 3

Twin City IM-4050 11Models DCRW/DCRWRMOUNTING BRACKET HOLE MOUNTING PATTERN 5/16" ANCHOR STUD (8) 6.78 6.78 D SQUARE A DIA. 2.00 MOUNTING BRACKE

Página 4 - Minimum Speed Setpoint

12 Twin City IM-4050Model DCLHBDAE SQUAREC2.00Dimensions and WeightsModel BCLHCBADF2.00 TYPE SQUARESIZEAMAX.B C DE SQ.CANTEDCURBDAMPERSIZEAVG. SHIP W

Página 5 - Belt Span

Twin City IM-4050 13Model DCLPE SQUARECB2.00 TYPADimensions and WeightsModel BCLPE SQUARE2.00 TYPBADCSIZEAMAX.B CE SQ.CANTEDCURBDAMPERSIZEAVG. SHIP W

Página 6 - MOTOR SHEAVE

14 Twin City IM-4050Seller warrants to the original purchaser that the goods sold hereunder shall be free from defects in workman-ship and material u

Página 7 - Motor Lubrication

Twin City IM-4050 15Refer to pages 6 and 7 for recommended maintenance.

Página 8 - Fan Troubleshooting Chart

5MWG10/14TWIN CITY FAN & BLOWER | WWW.TCF.COM5959 Trenton Lane N | Minneapolis, MN 55442 | Phone: 763-551-7600 | Fax: 763-551-7601

Página 9 - (DAMPER SIZE + 0.50 INCHES)

2 Twin City IM-4050Wall Fan Installation 1. Your wall fan is shipped with a wall mounting brack-et. Refer to the wall fan dimensional drawing

Página 10

Twin City IM-4050 3Roof Fan InstallationDownblast Fans: 1. Position the fan with its wiring conduit in line with the wiring coming up through t

Página 11

4 Twin City IM-4050Figure 3. Low End Setpoint AdjustmentNOTE: 5 amp model shown. On 10 and 15 amp models, adjustment is made through clear-ance hole

Página 12

Twin City IM-4050 5Figure 4. Eliminate Slack Figure 5. Belt DeflectionFigure 6. Alignment Figure 7. Two-Groove Sheaves (Pulleys)Figure 8. BeltsDefl

Página 13 - 2.00 TYP

6 Twin City IM-4050Three-Pulley (Idler Sheave) AssemblySingle bolt belt adjustment (Figure 9) can be made by loosening the idler sheave bolt (with 3/

Página 14 - FAN ASSEMBLY

Twin City IM-4050 7OIL TUBESFigure 10. Sleeve Bearing Motor Oil Tube LocationStorageIf fans are stored for any length of time, they should be stored

Página 15 - Twin City IM-4050 15

8 Twin City IM-4050Fan Troubleshooting Chart PROBLEM POSSIBLE CAUSES FAN DOES NOT OPERATE 1. Wrong voltage. 2. Electricity turned off or

Página 16 - 5MWG10/14

Twin City IM-4050 9Dimensions and WeightsModel DCRDModel BCRD-EModel BCRDA DIA.BC2.00"E SQUAREROOF OPENING(DAMPER SIZE + 0.50 INCHES)CURB SIZE

Comentários a estes Manuais

Sem comentários

Sharp R-210B Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Micro-ondas Sharp R-210B. Centrifugal Powered Roof & Wall Exhausters Manual do Utilizador

Resumo do Conteúdo

Comentários a estes Manuais

Manuais e produtos relacionados com Micro-ondas Sharp R-210B