Sharp PC-A500 Manual de Instruções Página 1

INSTRUCTION BULLETIN& MAINTENANCE MANUALFOR CTD A500MODELS A500, A500M10.01.12CTD MODEL NO:CTD SERIAL NO:MANUFACTURE DATE:DISTRIBUTOR PURCHASED TH

Guarding:The belt drive is completely enclosed with a fabricated guard. The blade guard coversand the machine shield mustbe down and closed for the m

SUGGESTED SPECIAL TOOLING FOR CUTTING ROUNDS ON A500Drill and tap to suit Front and back JawsBlades:High speed cut-off machines are a variation of a m

Air Supply:The air supply must be turned off and all electrics disconnected before making adjustments on the power feed.A working pressure of 75 P

-13-Air Hydraulic Power DownfeedCutting Speeds:The rate at which the blade cuts the material varies considerably depending on the type of:1. Material

Speed Control of Blade Movement:The downstroke speed of the blade is controlled by the Hydrocheck, P/N B3P146 or P/N B3P148 located next tothe main

Safety Instructions to the Operator: 1. KNOW YOUR CTD SAW. Read this instruction manual carefully. Learn the operation, application, and lim

How to Operate the Model A500:The control of all functions on the A500 are accomplished using a tablet PC(Windows 7 based) controller. Thecontroller

Irregular Mitres:Irregular mitre cuts are almost always caused by out-of square material. Check your material with a 90° squareand a straight edge.

400X Spindle Assembly and Bearing Installation Instructions:Refer to Spindle Diagram on previous page.Spindles are assembled using a fool-proof, tampe

-19- Right Side Shown,Left OppositeModel M516 ShownAir Cushion Knob

SUBJECT PAGE NO.Machine Requirements……………………………………………………………………………….. 2Installation and Set-Up……………………………………………………………………………….. 3Electrical Installa

-20-400S Blade Guard and Stand Exploded ViewModel M516 ShownRight Side Shown,Left OppositeAir Cushion Knob

-21-400S Blade Guard and Stand Parts ListModel M516 Shown

Miscellaneous Parts:4BF10 400 Series Handle4BF30 Rear Dust Outlet4BM32 Return Spring w/Washer4BM31 Downstop Block 400 Hand Operated4BM223-6’ 6’ Extend

RazorGage End-User Manual Technical Services, Inc Page 2 Topic Assembly Power Up Calibrate The Touch Screen Setup Screen Offset Calibration

RazorGage End-User Manual Technical Services, Inc Page 3

RazorGage End-User Manual Technical Services, Inc Page 4 To position the stop just punch in a number, press and the stop will go to tha

RazorGage End-User Manual Technical Services, Inc Page 5 To calibrate your touch screen, follow these steps: Press Press Control Panel D

RazorGage End-User Manual Technical Services, Inc Page 6 The setup screen is password protected. System parameters are protected by a different pa

RazorGage End-User Manual Technical Services, Inc Page 7 From the main screen, press Enter the user password 90210 Press Enter how long you w

Space RequirementsInstallation and Set Up:The CTD saw you have purchased is designed to cut wood, aluminum, plastic and steel, with of course the prop

RazorGage End-User Manual Technical Services, Inc Page 8 The RazorGage ships with 4 preset screens like the one shown at left. Each screen has 56

RazorGage End-User Manual Technical Services, Inc Page 9 The Auto Pusher Screen allows you to define cut routines for specific board lengths and s

RazorGage End-User Manual Technical Services, Inc Page 10 You may download workorders to your PC RazorGage with the Workorder Screen. Press the

RazorGage End-User Manual Technical Services, Inc Page 11 If your system has the optional Barcode Scanner, you need to calibrate it before using y

RazorGage End-User Manual Technical Services, Inc Page 12 1 2 3 4 5 The Autolist feature uses cutlists that have been run through the Parts List P

RazorGage End-User Manual Technical Services, Inc Page 13 Part Part No Bearing Rail RG10028 Drive Belt RG10108 Drive P

RazorGage End-User Manual Technical Services, Inc Page 14 Bearing Rail Drive Belt Drive Pulley Motor Gearbox Idler Pulley Idler Block Dust

RazorGage End-User Manual Technical Services, Inc Page 15 Phone 515.232.3188 Fax 515.232.2953 Email [email protected] Online http

Attaching Extended Fence Gage:1. Place Extended Fence Gage (5/8 x 3-1/2” material) on table. Bolt to fence bracket with screws provided.Adjust fence

These machines are general purpose in their design, therefore the user should attach any addi-tional guarding to the blade guard or table base if

Safety Instructions to the Operator: 1. KNOW YOUR CTD SAW. Read this instruction manual carefully. Learn the operation, application, andlimitations

Angle Adjustments on Model A500M:To change the angle:Clamping and Work Slippage:The work must never be allowed to move or vibrate as it is being cut.

Diagram “F” Vertical Clamp AssemblyRemoving Material From the Blade:If the machine is stalled while cutting, immediately shut saw off and disconnect p

Sawblade Lubrication System:The Sawblade Lubrication System is used when cutting aluminum or other non-ferrous materials. This systemnormally uses a