Sharp JW-20CM Manual do Utilizador Página 179
- Página / 230
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
10·11
10
Read out operation status of PC
Function Read out PC operation status of specified stations.
Command code 20
(H)
(MPC)
Writing mode assignment No
Operation condition of PC Unrelated
Data
Stop/restart operation of PC
Function Stop or restart PC’s operation of specified stations.
Command code 30
(H)
(HLT, RUN)
Writing mode assignment No
Operation condition of PC Unrelated
Data
· "Writing mode assignment" is used to show whether writing to the PC memory has been enabled or
disabled.
0: Writing prohibited
1: Enable writing only to data memory
2: Enable writing all data.
No setting: Enable writing in any mode
Letters in brackets are
command name of BASIC
mode.
CPfonoitidnocnoitarepO ataD
gnitarepogniruD00
)H(
eludomnoitporehtoybpotS10
)H(
03(TLAHybpotS
)H(
dnammoc)20
)H(
Letters in brackets are
command name of BASIC
mode.
CPfonoitidnocnoitarepO ataD
noitarepopotS00
)H(
noitarepotratseR10
)H(
- Version 2.2 1
- Produced in Oct. 1997 1
- Safety Precautions 3
- Caution 4
- Prohibit 4
- Network module JW-20CM 6
- - User’s Manual 6
- Table of contents 7
- Chapter 1 Outline 9
- Chapter 2 Safety Precautions 10
- Joint using a 11
- 2-3 Treatment 12
- 2-4 Static electricity 12
- 2-5 Maintenance 12
- 4-1 JW-20CM 14
- Set at delivery 15
- 4-2 JW-20RS 16
- Chapter 5 Installation 18
- ②③④ ⑤⑥ ⑦ 20
- (Ex.: JW-13BU) 20
- Control module 20
- Port number 20
- 2 rack panel max 21
- Phillips screwdriver 23
- Power supply module 23
- Module attachment 23
- The system consists of the 24
- Set the blade to within 25
- 1 mm in order not to 25
- When the adjustment 26
- KEDAADFS 27
- Chapter 7 Wiring 30
- 7-6 Check after wiring 34
- Chapter 8 Remote I/O 39
- × 8 points) 41
- Processing of JW-20CM 42
- Processing of PC side 42
- Hold time [ms] 45
- TerminatorTerminator 49
- Less than 1 km 49
- 1ledomWZfoeludomO/I 53
- 2ledomWJfoeludomO/I 53
- From the previous page 56
- Write in label 56
- (JW model or ZW model) 57
- O: Necessity for setting 57
- Operation procedure 58
- In brackets : See page 58
- Not setting dummy I/O 59
- HEX (hexadecimal) 60
- OCT (octal) 60
- DCM (decimal) 60
- Bit pattern 60
- Display on the JW-13PG 67
- (Light OFF) 67
- (8) = 00(H)) 69
- (8) = 81(H)) 69
- 17776 OCT 000 72
- 17777 OCT 000 72
- >00000 OCT 014 72
- 00000 0 005014 78
- 00002 0 000200 78
- >00004 0 101000 78
- 00200 DCM 000 80
- 00201 DCM 008 80
- >00202 DCM 010 80
- □□□□□□□□ 81
- □■■■■■■■ 81
- 76543210 0 0 83
- (8) etc 83
- 8-4 Error and treatment 84
- ② JW-20RS 86
- Indication lamp 86
- All stations 89
- Slave station 77(8) 89
- Chapter 9 Data Link 99
- 9-2 Communication method 100
- Target station 106
- 64 bytes 107
- 00000 F–44 02030 02000 112
- 02000 02030 112
- 9-4 Expansion of network 113
- : Master station 114
- : Slave station 114
- Terminator: ME-75 117
- Coaxial cable 118
- Turn “ON” shield ground 118
- Corresponding 120
- 11·7 and 11·8 120
- When not using 121
- SEND/RECEIVE function 121
- When not using memory 121
- Screen display of JW-13PG 122
- Setting 125
- 07714 D 00000 126
- 07716 D 00000 126
- I PARAM 126
- >07720 D 00004 126
- 07726 0 000000 127
- 07730 0 001000 127
- >07732 0 000000 127
- HAM1-WJ,AM1-WZ1ro0 ※ 128
- HAM2-WJ,AM2-WZ1ro0 128
- HAM3-WJ,AM3-WZ2,1,0 128
- HAM4-WJ,AM4-WZ7,6,5,4,3,2,1,0 128
- Contents 130
- bytes bytes bytes 133
- 24 24 24 134
- →Bit pattern 137
- After converting to octal 138
- (4 bytes) 139
- 004004(8) 140
- 004010 to 004011(8) 141
- File number of communication 148
- File number 149
- 9-8 Error and treatment 151
- (2) Flag 153
- Communication monitor 158
- 76543210 160
- Port 7 error 160
- Port 5 error Port 3 error 160
- Chapter 10 Computer link 169
- 10-2 Communication method 170
- 10-3 Switch setting 171
- 10-4 Command 172
- CPfonoitidnocnoitarepO ataD 179
- )FFO(000 182
- Chapter 11 Support Tools 188
- 11-2 Remote function 192
- Satellite net 193
- (JW-50PG) 194
- Chapter 12 Specifications 198
- 12-2 JW-20RS 201
- Chapter 13 Appendix 202
- 13-2 Switch setting table 203
- 13-3 Parameter memory table 204
- (8) are all 00(H) 205
- (8) Set contents 206
- (8) I/Os are JW models 208
- (8) are all 91(H) 215
- Bit address 76543210 216
- ③ Data link slave station 217
- Slot: 1 Slot: 0 220
- (File 0) 221
- HAM4-WJ,AM4-WZ7,6,5,4,3,2,2,0 222
- Top address for 223
- Completed receiving flag 225
- Power module 227
- Port No 227
- Send Data 228
- Receive Data 229
- Target Station 230
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais