Sharp XG-MB70X Guia de Início Rápido

MODELXG-MB70XMULTIMEDIA PROJECTORSETUP GUIDEScreen Size and Projection Distance ... 2Connecting Pin Assignments...

-10Setting up the Projector Network Environment3. Setting up a NetworkConnection for theProjectorSettings for such items as the projector’s IPaddress

-114 The TCP/IP setting screen ap-pears, ready for network settingsfor the projector.Note• Confirm the existing network’s segment (IPaddress group) to

-12Controlling the Projector via LANControlling the ProjectorUsing Internet Explorer(Version 5.0 or later)Complete connections to external equipmentbe

-13Confirming the ProjectorStatus (Status)On this screen, you can confirm the projectorstatus. You can confirm the following items :••••• MAC Address•

-14Controlling the Projector via LANSetting and Adjusting theProjector (Setting & Adjustment)Example: “Picture” screen display for INPUT 1On these

-15Controlling the Projector via LANMaking General Settingsfor the Network (Network -General)On this screen, you can make general settingsrelating to

-16Controlling the Projector via LANSetting Error Items andDestination Addresses towhich E-mail is to be Sentwhen an Error Occurs(Mail – Recipient Set

-17Setting the Projector Using RS-232C or TelnetWhen Connecting UsingRS-232C1 Launch general purpose terminalemulator.2 Input settings for the RS-232C

-18Setting the Projector Using RS-232C or TelnetWhen Connecting UsingTelnet1 Click “Start” from the Windows® desk-top and select “Run”.2 Enter “telnet

-19Setting the Projector Using RS-232C or TelnetSETUP MENU (Main Menu)[1]IP Address (Factory default setting : 192.168.150.2)IP address settings. (Pag

-2Picture (Screen) size Projection distance [L]Diag. [χ] Width Height Minimum [L1] Maximum [L2]250" (635 cm) 553 cm (218") 311 cm (123"

-20Controlling the Projector Using RS-232C or TelnetView Setting Detail List([V]View All Setting)11111 Enter “v” and press the “Enter” key.Display all

-21Controlling the Projector Using RS-232C or TelnetSave Settings and Quit([S]Save & Quit)Save set values and quit menu.11111 Enter “s” and press

-22Controlling the Projector Using RS-232C or TelnetIP Address Setting([1]IP Address)Setting of IP address.11111 Enter “1” and press the “Enter” key.2

-23Controlling the Projector Using RS-232C or TelnetUser Name Setting([4]User Name)Carrying out security protection using user name.11111 Enter “4” an

-24Controlling the Projector Using RS-232C or TelnetDisconnecting All Connec-tions ([D]Disconnect All)It is possible to disconnect all the TCP/IP conn

-25Controlling the Projector Using RS-232C or TelnetCarrying out Network PingTest(ADVANCED[5]Network Ping Test)It is possible to confirm that a networ

-26Controlling the Projector Using RS-232C or TelnetSetting of Search Port(ADVANCED[0]Search Port)Sets the port number used when searching for theproj

-27TroubleshootingCommunication cannot be established with the projectorWhen connecting the projector using serial-connection\ Check that the RS-232C

-28Troubleshooting\ Take the following steps for checking the network settings for the computer.1. Open a command prompt (MS-DOS Prompt).• In the case

-29\ Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, checkif an IP address is set.1. Open a command prompt (MS-D

-3RS-232C Terminal: 9-pin Mini DIN female connectorPin No. Signal Name I/O Reference1 Not connected2 RD Receive Data Input Connected to internal circu

-30DimensionsUnits: inches (mm)Side View Side ViewTop ViewRear ViewFront ViewBottom View1/8 (3.25)11 7/64 (282)1/16 (1.5)2 11/64 (55.05)12 13/64 (310)

-4StandbyPower ONPower StatusProjector StatusLamp StatusVolume (0-60)AV Mute : OFFAV Mute : ONKeystone (-127 ~ +127)INPUT1 (RGB1)INPUT2 (RGB2)Freeze :

-5RS-232C Specifications and CommandsNote• If an underbar (_) appears in the parameter column, enter a space.• If an asterisk (*) appears in the para

-6Page 71. Connecting the projector to a computerSetting up the Projector Network EnvironmentThis section describes the basic procedure for using the

-7Setting up the Projector Network Environment1. Connecting the Pro-jector to a ComputerEstablishing a one-to-one connection from theprojector to a co

-8Setting up the Projector Network Environment2. Setting an IP Addressfor the ComputerThe following describes how to make settingsin Windows® XP (Prof

-9Setting up the Projector Network Environment12After confirming or setting, proceed to “3. Setting up Network Environment for the Projec-tor”.5 Click